How To Make Wooden Poker Chip Trays

Posted on  by

Poker Table Dealer Chip Trays. The Poker Table Dealer Chip Trays are designed to sit into the table and requires a hole to be cut. They provide storage for chips right at the table for extra convenience. They are a must if you have a dealer spot at your table. 300 Chip Dealer Chip Tray. $10.00 - $10.99. Add to Cart Details. Make Offer - Unusual wooden bullet shaped poker chip holder with miscellaneous chips Used Paulson Plastic Poker Chip Trays (Lot of 13) Trump Plaza Paul-Son Rack SEE $59.99.

Helpful Links

What may be causing this?

  • You are attempting to access this page via a Webhosting Account
    • Scripted access to public pages is not allowed.
  • You are accessing the web via a proxy.
    • If you are using a public proxy, you may wish to switch to another or disable it. If you believe your ISP is using a transparent proxy, please let us know.
  • You or someone on your network is running a bot to crawl our site.
    • Please contact your Network Administrator if you believe this to be the case.

We just need you to confirm that you are a person and not a robot.

Build your own high quality poker table with this FREE downloadable PDF

Click here for the >>>Poker Table Plans<<< (PDF version of the instructions below)

These poker table plans contain step-by-step instruction for how to build a poker table. The table will measure 48' x 96' and have a 4' wide rail. This will provide adequate seating for 10 players.


These instructions use pine boards for the legs and frame, because these are painted. If you prefer to stain you table, you may want to substitute for a different species of wood. You may also to purchase foldable steel table legs. This will cut down on cost and time.

Poker Table Supplies needed:

  • 3 - 4'x8' Sheet of ¾ ' Plywood or MDF
  • 10 - 8' 1x4 Select Pine Boards
  • 1 - 6' 1x10 Select Pine Board
  • 4 - Black Strap Hinges
  • 4 - Table Leg Braces
  • Quality Wood Glue
  • 1 can - 3M Spray Adhesive
  • 1 qt. of Paint (black)
  • 1 qt. of Polyurethane
  • 8 - 2' Bolts with Tee Nuts
  • 1 - Box of 1 ¼ ' Black Drywall Screws
  • 16 - 4' Black Drywall Screws
  • Wood Filler
  • ¼' Closed Cell Table Foam 96'x48'
  • 21’ - Rail Foam
  • Poker Table Rail Vinyl
  • Poker Table Felt
  • Optional - 2 Foldable Poker Table Legs (Remove 7 - 8' 1x4 Select Pine Boards)
  • Other optional items: poker table cup holders, dealer chip trays and money boxes.

Tools

  • Jig Saw
  • Miter Saw with Finish Blade
  • Belt Sander with 120 grit sand paper
  • Orbital Sander with 180 grit sand paper
  • Router
  • ¼ ' Roundover with bearing' Router Bit
  • Drill
  • Drill Bits (3/4' Spade, 1/8' wood, ¼ ' wood, 5/16' wood)
  • Countersink
  • Clamps
  • Utility Knife
  • Hammer
  • Staple Gun
  • Staples
  • Paint Brush or Sprayer

Step 1 - Create Poker Table Plans on Plywood

Draw your Table/Rail pieces onto the 3 pieces of Plywood. The table top will be 1 piece and the rail will consist of 3 pieces (top, middle and bottom).

The First Sheet of 48' x 96' Plywood

The first sheet will produce the bottom piece of the rail and the table top.

Locate the spot 24' in from the end and 24' in from the side; mark it. Do the same at the other end. These are the spots that will produce the radiuses for the semi circles.

The first Semi circles will be for the outside edge of the bottom rail piece. Measure out 24' from the marked spots (this will be to the edge of Plywood). Draw a semi circle from one side of the sheet of plywood to the other creating the semi circle. Repeat on other end.

The second semi circle will be for the inside edge of the bottom rail piece. Measure 22 ½ ' from the marked spot. Draw a semi circle on both ends. Now draw a straight line along both sides to connect the two semi circles.

The Third semi circle to will be for the table top piece. Measure 22 ¼ ' from the marked spot. Draw a semi circle at both ends. Now draw a straight line along both sides to connect the two semi circles.


Second and Third Sheets of 48' x 96' plywood

These sheets will produce the middle and top pieces of the rail.

Again, locate the spot 24' in from the end and 24' in from the side; mark it. Do the same at the other end.

How To Make Wooden Trays

Measure out 24' from the marked spot and draw a semi circle. Repeat on other side. This created the outside edges of the rail.

Measure out 20' from the marked spot and draw a semi circle. Repeat on other side. This has created the inside edges of the rail.

This will create a 4' wide rail.

Repeat these same steps on the third sheet of plywood.


Step 2 - Cut out Table Top and Rail Pieces

Use a jig saw to cut the 4 pieces out of the Plywood. First, cut off the corners. Next drill a pilot hole for the jig saw blade. Use a ¼ ' drill bit. Drill the hole next to the line, not into it (also not into the table or rail piece). Once the holes are drilled, and then cut out the remaining pieces.


Step 3 - Assemble Rail Pieces

The next step is to assemble the rail. These pieces will be glued and screw together. Dry fit the 3 pieces together to see which way they fit the best.

Assemble Top and Middle Piece

First, apply wood glue to one side of the top piece. Next, lay the middle piece on top of the top piece. Make sure they are lined up together. Clamp them together. Use a 1/8' drill bit and drill pilot holes every 8' - 12' around the rail. Use a countersink on the hole, so the screw will be recessed into the wood. Screw 1 ¼ ' sheetrock screws into the holes. Remove clamps.


Assemble Bottom piece to Top/Middle Pieces.

Apply glue on one side of the bottom piece. Lay the bottom piece onto the other pieces. Make sure pieces are lined up together. Clamp pieces together. Use a 1/8' drill bit and drill pilot holes every 8' - 12' around the rail. Use a countersink on the hole, so the screw will be recessed into the wood. Screw 1 ¼ ' sheetrock screws into the holes. Remove clamps. Fill each of the screw holes with wood filler. Allow the wood filler to dry.

Step 4 - Sanding Rail and Table Top

Table Top -

Sand the side of the Table Top to remove any roughness or unevenness from sawing using a belt sander.

Rail -

All of the edges of the rail need to be rounded. This can be done with a belt sander, but preferably to be done with a router. Using a ¼ ' Roundover with bearing' router bit works great. Each of the 5 edges should be rounded.

Use the belt sander to sand the side of the rail. Try to make it as smooth as possible. Use the orbital sander to lightly sand the top and the newly rounded edges. Make sure that the wood filler is sanded smooth.


Step 5 - Seal Rail and Table Top

Apply a thin coat of polyurethane to the top side and edge of the table top, and to all sides of the rail. Put these pieces aside and let them dry. This does two things; protects the wood from spilled liquids and most importantly helps the spray adhesive adhere better.

Step 6 - Table Frame

Cut Frame Pieces

  • 2 - 31 7/8' 1x4 boards - End Pieces
  • 2 - 64' 1x4 boards - Side Pieces
  • 1 - 30 3/8' 1x4 board - Middle Support
  • 2 - 30 3/8' 1x10 boards - Leg Mounts

You will cut a total of 7 pieces for the frame. Use 3 of the 8' 1x4 and 1 6' 1x10 boards for the frame. Use one of the 1x4 boards; cut 2 - 31 7/8' length pieces and 1 - 30 3/8' length piece. Next, cut 2 - 64' length pieces, one out of each of the 2 remaining 1x4 boards. Finally, cut 2 - 30 3/8' length pieces out of the 1x10 board.

Assemble Frame Pieces

At both ends of the end pieces, countersink two pilot holes. The side pieces will butt up to the end pieces. Apply wood glue to the ends of the side pieces. Fit the end and side pieces together. Use 8 - 1 ½ ' sheetrock screws to fasten them together. This will make a rectangular shaped frame.

At the halfway point (32 ¾ ') of the now 65 ½ ' side, drill 4 countersink pilot holes, 2 holes on each of the sides. Apply glue to the ends of the 30 3/8 1x4 middle support piece. Insert it into the frame and fasten it in place with 4- 1 ½ ' screws.

The 2 - 30 3/8' 1x10 leg mount boards go in next. These boards will sit flush with the top edge of the frame. Drill 10 countersink pilot holes for each leg mount board; 3 holes on each side and 4 on the end. Apply glue on three edges of the leg mount board. Insert it into the frame and fasten it in place. Fill all screw holes with Wood Filler.


Step 7 - Attach Frame to Table Top

Have the table top laying flat with the bottom side up. Lay the frame on top of the table top. Make sure that the frame is centered in both directions on the top. Use a pencil to outline the frame onto the table top. Outline both inside and outside of frame, including the center support and leg mounts.


Step 8 - Table Legs

Rough Cut Leg Pieces

  • 16 - 27' 1x4 (These will be cut to 26' later)
  • 8 - 24' 1x4 (These will be cut to 23 ¾ ' later)

Cut 15 - 27' 1x4 pieces out of 5 - 8' 1x4 boards. Cut the 16th 27' piece out from one of the left over 32' pieces from the frame. These 16 boards will make the 4 legs.

Cut 8 - 24' pieces out of the remaining 2 - 8' 1x4 boards. These 8 boards will make the 2 cross supports for the legs.


Glue Leg Pieces

Divide the 16 - 27' legs boards into 4 groups of 4. Glue the 4 boards together and clamp them together. Repeat this for the other 3 legs. Allow the glue to set before removing clamps.

Divide the 8 - 24' support boards into 2 groups of 4. Glue the 4 boards and clamp them together. Repeat this for the other support. Allow the glue to set before removing clamps.


Sanding Leg Pieces

Use a belt sander and sand the leg and support pieces smooth. Only sand the joint side of these pieces. Next, use the router with the ¼ ' Roundover with bearing' bit and round the corners of the legs and support pieces. Use the orbital sander to sand the pieces to a nice smooth finish.


Finish Cut Leg Pieces

Finish cut each leg to 26 ½ '. Cut off a portion of each end of each leg to ensure that both ends of the leg have a finished cut. Light sand with the orbital sander.

Finish cut each Support to 23 ¾ '. Cut off a portion of each end of each support to ensure that both ends of the support have a finished cut. Light sand with the orbital sander.

Assemble Legs

The 4 legs will measure 3' x 3 ½ ' in width. Lay the 4 legs side by side with the 3 ½ ' side face up. Measure up from the bottom of each leg 5' and 8 ½ '. Mark these measurements across each leg. This is the location were the cross supports will fasten to the legs.

Drill four 3/16' holes completely though the each leg. Use a countersink bit or 3/8' drill bit and make a ½ ' to ¾ ' deep countersink hole for each of the 16 screw holes. Apply wood glue to both ends of each of the support pieces. Insert the screws into the holes and fasten the leg to the support. Do this for each leg.


Wipe off any excess glue. Fill the screw holes with wood filler. Once the glue and wood filler is dry, sand those areas smooth with the orbital sander.


Step 9 - Paint Table and Legs

You will be painting the legs, frame and bottom of table. Apply the paint which ever way is easiest for you; spray paint, brush or sprayer. First apply a coat of primer. You will need to do 2 coats. Allow drying time between coats.


Step 10 - Install Legs to Table

Lay the table top flat with the bottom face up. Place the legs into their positions. Have the legs tight up against the frame on the ends; leave an equal space between the legs and the side frames. Install the strap hinges and table leg braces. Flip the table over and stand it up with the legs down.


Step 11 - Install T-Bolt Nuts into Rail

Position the rail into place on the table. From underneath the table make sure there is an even gap between the table and rail. This gap is needed for the felt and vinyl. Once the rail is positioned correctly, clamp it in place.

Trays

You will be drilling 8 holes evenly spaced around the rail, these holes should be 1 1/8' in from the inside edge of the rail. Using a ¾ ' spade drill bit, drill 8 holes to a depth of ½ ' - ¾ '. Using a 5/16' wood drill bit, drill through the remaining depth of the rail and through the table.


Remove the rail from the table. Gently pound each of the T-bolt nuts into the holes. Put a ¾ ' piece of board under the lip of the rail to provide support, so the rail is not damaged. Secure rail back on the table, by screwing in place with all 8 bolts. Fill in the ¾ ' holes with wood filler. Sand when dry.

Step 12 - Install Foam

Both the table and the rail need to have the foam applied to them.

Table Foam

Spray the top of the table with adhesive. Lay the ¼ ' closed cell foam onto the table. Press the foam down in the middle and work it out to the edge. Make sure you work out any air bubbles.

Locate the holes for the rail bolts and cut them open.


Rail Foam

Glue to rail foam to the top of the rail. Make sure you have enough foam hanging over the sides to cover the sides of the rail

.

Start at a midway point on one of the straight sides. Work in 2 foot section at a time. Spray glue onto the top of the rail. Place foam onto the area which you just sprayed glue. Once it has adhered to the rail work on the next 2 foot section. Continue this all the way around. When you get all of the way around, overlap the foam and use a utility knife to cut the joint. Then glue the final section down, making sure the ends a tight to each other.

Next Glue the sides down and even wrap around to the bottom of the rail. Then trim off all of the excess using a utility knife.


Step 13 - Poker Table Felt

Lay the Felt out on the table with an even amount over hanging on the sides. Use a staple gun to fasten the felt to the table. You will be stapling the felt into the edge of the table.

Start at the middle of one of the long sides. Put in 1 staple. Go to other side and pull the felt tight. Put one staple in. Go to one of the round ends. Pull the felt tight and put 1 staple in. Go to other end and pull it tight and put 1 staple in. Go halfway between two of the staple and pull it tight and put in 1 staple. Then go to other side and repeat. Continue doing this until the whole piece of felt is tight and in place. Staples should be 3' - 4' apart.

Tray

Use a utility knife and cut off all the excess felt. Cut it off even with the bottom surface of the table. Use a hammer to gently pound in any staples that are not completely in.

Locate the holes for the rail bolts and cut them open.


How To Make Wooden Poker Chip Trays

Step 14 - Rail Vinyl

This can be a tricky part of the job, especially if you are using vinyl that does not stretch very well. The vinyl we have for sale at this site stretches very nicely making this part a little easier.

Lay the Vinyl flat with the black side face down. Lay the rail onto the vinyl, top side down. Make sure the rail is centered in the vinyl. The vinyl will completely cover every surface of the rail. The seam will be located at the inside corner on the bottom side of the rail.


Wood Poker Chip Tray

Start at the middle of a round end. Pull the vinyl up and over to the inside edge and put 1 staple in place. Go to the other end and do the same thing. Take the utility knife and cut down the center of the vinyl inside of the rail. Make the cut about 5' in length parallel to the straight sides of the rail. (The reason for this is that you will be pulling the vinyl out on the sides which will then help it go around the round ends.)


Gently pull the vinyl at the middle of one of the sides, so the cut that you put down the middle starts to pull open about 3'. Then put a staple into the inside edge. Repeat on other side. The middle cut should be about 6' wide in the center.

You will do the outside edge of the straight sides first. Work your way down from the first staple to where the rail begins to round. Gently pulling the vinyl up and over and staple to the inside edge. Then work your way the other direction from the center and then to the other side.

Once the vinyl is wrapped around the outside and stapled in place, take the utility knife and run it down inside edge of the rail and remove all of the excess vinyl. Use a hammer to gently pound in any staples that are not completely in.

It is now time to wrap it on the inside of the straight sides. Use the utility knife and cut from the ends of the existing cut, straight towards each side and 3 cuts towards the rounded end of the rail; making 4 triangle shaped pieces. Cut until you are about 4' from rail. Now take the side sections of vinyl and pull them tight and staple it in place. Start in middle and then work in each direction. Run Utility knife down inside edge and remove excess vinyl.


Next, wrap the inside of the round ends. Cut the triangle shaped pieces in half, making 8 triangle shaped pieces. Start on one side and take the first pieces and pull it tight and staple it in place. Continue around the end of the rail stapling each piece into place. Repeat on other side and trim off excess vinyl.


The outside of the round ends is the most difficult part of the vinyl. You need to firmly stretch the vinyl up and over the rail and staple it. The end of the rail vinyl is already stapled. Start halfway between the end and the side. Then just keep going halfway between the stapled points, until it is all stapled in place. The trick here is to try to not have any creases in the vinyl. Once you have both ends stapled in place, then cut off any excess vinyl. Located the holes for the rail bolts and cut them open.

How To Make Wood Trays


Poker Table Chip Tray Inserts

Step 15 - Attach Rail to Table

Put the rail in place on the table. Place a washer on each bolt. Tighten each of the bolts through the bottom of the table into the rail.

Poker Chip Trays For Sale